WiFi Pineapple Mark VII
  • WiFi Pineapple Mark VII
  • Setup
    • Connecting the WiFi Pineapple
    • Setting up your WiFi Pineapple
    • Connecting to the WiFi Pineapple on Linux
    • Connecting to the WiFi Pineapple on Windows
    • Setting up the WiFi Pineapple over WiFi
    • Setup by USB Disk
  • UI Overview
    • Introduction to the UI
    • Dashboard
    • Campaigns
    • PineAP
    • Recon
    • Handshakes
    • Modules
    • Settings
    • Cloud C²
  • Developer Documentation
    • Developer Resources
    • Contributing to the Module Repository
  • WiFi Basics
    • Introduction to WiFi
    • Radios and Chipsets
    • Stations and APs
    • Transmit Power
    • Antennas
    • Channels and Regions
    • Protocols
    • Modes of Operation
    • Logical Configurations
    • MAC Addresses
    • Broadcast and Multicast MAC Addresses
    • SSIDs
    • 802.11 Frame Types
    • 802.11 Frame Structure
    • Management Frames
    • Frame Injection
    • Association and State
  • FAQ / Troubleshooting
    • MacOS Support
    • Establishing an Internet Connection
      • Configuring a Client Mode Connection
      • ICS on Linux
      • Configuring ICS on Windows
      • Configuring a USB Ethernet Adapter
    • Password Reset
    • Factory Reset and Recovery
    • WiFi Pineapple Updates
    • WiFi Pineapple Beta Updates
    • Compatible 802.11ac Adapters
  • Extras
    • MK7 LED Mod Installation
    • MK7 Kismet Case Installation
Powered by GitBook
On this page
  • Cloud C²
  • Connecting to Cloud C²
  • WiFi Pineapple and Cloud C²
  • Disconnecting from Cloud C²

Was this helpful?

  1. UI Overview

Cloud C²

Connecting the WiFi Pineapple to Cloud C²

Last updated 3 years ago

Was this helpful?

Cloud C²

Cloud C² makes it easy for pen testers and IT security teams to deploy and manage fleets of Hak5 gear from a simple cloud dashboard.

Cloud C² is a self-hosted web-based command and control suite for networked Hak5 gear that lets you pentest from anywhere.

Linux, Mac and Windows computers can host the Cloud C² server while Hak5 gear such as the WiFi Pineapple, LAN Turtle and Packet Squirrel can be provisioned as clients.

Connecting to Cloud C²

Once you have Cloud C² , adding a WiFi Pineapple to your server is simple!

  1. Create a device in your Cloud C² instance

  2. Download the device configuration file

  3. Navigate to "Settings" on the WiFi Pineapple

  4. Click the "Choose File" button in the Cloud C² card

  5. Upload your configuration file

WiFi Pineapple and Cloud C²

Once connected to a server, the Cloud C² service takes over most configuration and operation of the WiFi Pineapple.

Typical operations such as starting, stopping, and viewing recon scans, configuring filters, etc, are managed centrally by the Cloud C² server, and the local WiFi Pineapple UI is paused. The Cloud C² alert on the WiFi Pineapple allows for basic network configuration.

Should you find it necessary to make changes to the WiFi Pineapple locally, the UI can be re-enabled by the "Access UI" button.

Warning - The Cloud C² server will overwrite some configuration options, such as the PineAP and Recon Scan controls. Local control of the WiFi Pineapple while connected to Cloud C² should only be used for configuration changes that cannot be made remotely.

Disconnecting from Cloud C²

Your WiFi Pineapple can be unsubscribed from Cloud C² by clicking the "Remove Configuration & Reboot" button.

If you are in Local UI Bypass mode, it can be unsubscribed by navigating to "Settings" and using "Remove Configuration File" in the Cloud C² card.

installed and configured
following these steps
Uploading a Cloud C² configuration
A WiFi Pineapple running under Cloud C²
Removing the Cloud C² connection from Settings